Skip to content

Canon Ts3400 setup

A flexible all-in-one printer, the Canon TS3400 setup series is intended for usage in homes and small offices. It is seamless for a variability of happenings because it can print, scan, and copy. Because of the printer’s wireless connection, customers may easily print from PCs, cellphones, and tablets. Any workstation can accommodate the TS3400 thanks to its small size. It has an easy-to-use interface with a straightforward control panel. Convenient mobile printing and scanning are made possible by the printer’s compatibility with Canon’s Print app. In general, the TS3400 blends practicality and user-friendliness for routine printing requirements.

Canon Ts3400 Manual Setup

  • Take out the printer’s packaging and unpack it.
  • On the printer, plug in the power cord and push the power knob.
  • Install the included black and color ink cartridges after opening the front cover and shutting it.
  • Load plain or picture paper into the paper tray and adjust it.
  • Use the included CD or download the printer driver from Canon website.
  • Hold down the Wifi knob until it flashes, then use your smartphone to finish the Wifi setup.
  • This concludes the Canon TS3400’s basic manual setup.

Canon Ts3400 WPS Setup

Use these procedures to configure the Canon ts3400 wireless setup:

  • Verify that the Canon TS3400 is turned on.
  • Press your Wifi router’s WPS knob. The “WPS” label or the WPS icon may be shown on the knob.
  • Hold down the printer’s Wifi knob until the power lamp flashes once.
  • Press the Wifi knob once more after releasing it. The blue flashing of the Wifi bulb will begin.
  • The printer will look for the router on its own. After connecting, the power and Wifi LEDs will remain on and cease flashing.
  • To confirm the connection, print out a network information page.
  • The WPS setup is now complete.

Canon Ts3400 Setup with App

Here’s how to use the Canon PRINT Inkjet/SELPHY app to configure the Canon TS3400:

  • Get the Canon PRINT Inkjet/SELPHY app installed.
  • Verify that the Canon TS3400 is turned on.
  • Holding down the Direct knob on the printer will cause the Wifi light to flash.
  • To link the device to the printer’s Wifi, use the Canon PRINT app and adhere to instructions.
  • The printer will be immediately detected by the app; to register it, complete the configuration.
  • To validate the connection is working, run a test print or scan.
  • Wireless printing and scanning from device is now possible.

Canon Ts3400 Setup Issues

The following are typical Canon TS3400 printer configuration problems:

  • Wifi Connection Failure: Incorrect Wifi credentials or network interference are frequently the cause of the printer’s inability to connect to the wireless network.
  • Printer Not Found: It’s possible that incorrectly configured settings or incompatible devices are the reason why the device isn’t showing up in the Canon PRINT app.
  • Incorrect Mode: The app may not connect if the printer is not in Canon ts3400 wireless setup mode.
  • Issues with Driver Installation: Computers may experience communication problems if drivers are not installed correctly.
  • Mobile App Crashes: On outdated devices, the Canon PRINT app may not work or crash.
  • Firmware Outdated: The app may not work properly if the printer’s firmware is obsolete.
  • Paper Jam: Paper jams can cause disruptions during Canon ts3400 setup.

Canon Ts3400 Setup Solutions

The following fixes address typical Canon TS3400 setup problems:

Failure of the Wifi Connection:

  • Validate your wireless network is reliable and accessible.
  • Verify again that password and SSID are typed correctly.
  • Try reconnecting subsequent to restarting the printer and router.

No Printer Found:

  • Make sure that your printer and device are allied to an identical wireless network.
  • Try reconnecting afterwards and restarting the Canon PRINT app.
  • Pressing the Direct knob on the printer will activate wifi mode.

The wrong mode:

  • Holding down the Wifi knob until the power light flashes will put the printer in Canon ts3400 wireless setup mode.

Issues with Driver Installation:

  • Visit Canon website ij start canon to get the most recent drivers.
  • Once installation is comprehended, restart the computer.

Crashes in Mobile Apps:

  •  To fix incompatibilities, update or reinstall the Canon PRINT app.

Outdated Firmware:

  • Use the Canon PRINT app to find and install the most recent printer firmware updates.

Paper Jam:

  • Before proceeding with the Canon ts3400 setup, unclog any paper jams.

Canon ts3400 Reset

Use these procedures to reset the Canon TS3400 printer:

  • Validate the printer is not in use.
  • Holding down the Stop knob will cause the Power knob to push. Hold down the Power knob and let go of the Stop knob.
  • After five presses of the Stop knob, let go of the Power knob. At this point, the printer will go into service mode.
  • To return all settings to factory defaults, press the Stop knob four times.
  • To finish the reset, switch the printer off and back on.
  • You will need to reconfigure the printer and reconnect it to the network after reset.
  • All settings, including Wifi connections, are cleared throughout this procedure.

Canon ts3400 Firmware Update

Use these procedures to upgrade the Canon TS3400’s firmware:

  • Verify that the Canon TS3400 is turned on and allied to the internet.
  • Validate that device has a Canon PRINT Inkjet/SELPHY app.
  • Open the application and plug it into your printer.
  • Go to the maintenance or printer settings area of the program.
  • Locate and press the “Firmware Update” option.
  • Let the printer restart and update.
  • Validate the printer is operating correctly by testing it after the upgrade.